ShopKeep iPad Stand

The ShopKeep iPad Stand is a versatile way of displaying a register at checkout. Learn how to set up the stand with or without an iDynamo credit card reader and how to remove the PivotTable rotation base if desired.

Separate versions of this stand are available for iPad Air and iPad mini, but setup is the same for each.

Table of Contents

In the Box

The ShopKeep iPad Stand ships with all of the parts listed below.

Click to Enlarge
  • ShopKeep iPad Stand
  • 4 Adapter Clips
  • Foam for Adapter Clips (iPad mini version only)
  • 2 Assembly Tools (for the stand and PivotTable)
  • PivotTable Rotation Base (ships attached to the stand)
  • 2 PivotTable Adhesive Disks
  • Stand Setup - With iDynamo

    Install your iPad and iDynamo credit card reader in the ShopKeep Stand using the included assembly tool, screws, and brackets. If you don’t have an iDynamo, follow the setup steps in the next section instead.

    After setup, visit our best practices guide to learn how to care for the stand.

    1. Place the stand face down on a flat surface.
    2. Using the assembly tool, remove the screws and bracket on the side with 2 screws.
      Click to Enlarge
    3. Loosen, but do not remove, the 4 screws on the other side.
      Click to Enlarge
    4. Spread apart the 2 supports located on the side with 4 screws.
      Click to Enlarge
    5. Position the iDynamo face down between the supports and close them on the reader.

      The ridges on the supports fit into the holes on each side of the iDynamo.

      Click to Enlarge
    6. Attach an adapter clip to each of the 2 notches on the bracket still connected to the stand.
      • Adapter clips are required for all iPads except the 5th-gen iPad and 1st-gen iPad Air.
      • For the iPad mini 4, put the included foam between the clips and iPad for a more secure fit.
      Click to Enlarge
    7. Slide the iPad face down under the bracket and connect it to the iDynamo.
      Click to Enlarge
    8. On the removed bracket, attach an adapter clip to each of the notches.
      Click to Enlarge
    9. Place the bracket over the unsecured side of the iPad and reinsert the screws.
      Click to Enlarge
    10. Gently tighten all 6 screws until you begin to feel resistance.

      Be careful not to over tighten.

    11. (optional) Affix an adhesive disk to the bottom of the PivotTable base.
      • The permanent disk has adhesive on both sides, allowing the stand to be adhered to a surface.
      • The temporary disk has foam on one side, allowing the stand to be moved around as needed.
      Click to Enlarge
      Don’t want the stand to rotate or prefer to bolt it down? Follow the steps to remove the PivotTable.

    Stand Setup - Without iDynamo

    Install your iPad in the ShopKeep Stand using the included assembly tool, screws, and brackets. If you have an iDynamo credit card reader, follow the setup steps in the section above instead.

    After setup, visit our best practices guide to learn how to care for the stand.

    1. Place the stand face down on a flat surface.
    2. Using the assembly tool, remove the screws and bracket on the side with 2 screws.
      Click to Enlarge
    3. On the other side, remove the 2 outer screws and the 2 iDynamo supports.
      Click to Enlarge
    4. Loosen, but do not remove, the 2 remaining screws.
    5. Attach an adapter clip to each of the 2 notches on the bracket still connected to the stand.
      • Adapter clips are required for all iPads except the 5th-gen iPad and 1st-gen iPad Air.
      • For the iPad mini 4, put the included foam between the clips and iPad for a more secure fit.
      Click to Enlarge
    6. Slide the iPad face down under the bracket.
      Click to Enlarge
    7. On the removed bracket, attach an adapter clip to each of the notches.
      Click to Enlarge
    8. Place the bracket over the unsecured side of the iPad and reinsert the screws.
      Click to Enlarge
    9. Gently tighten all 6 screws until you begin to feel resistance.

      Be careful not to over tighten.

    10. (optional) Affix an adhesive disk to the bottom of the PivotTable base.
      • The permanent disk has adhesive on both sides, allowing the stand to be adhered to a surface.
      • The temporary disk has foam on one side, allowing the stand to be moved around as needed.
      Click to Enlarge
      Don’t want the stand to rotate or prefer to bolt it down? Follow the steps to remove the PivotTable.

    Remove PivotTable Base

    The optional PivotTable gives cashiers the ability to swivel the register. Remove the PivotTable if you don’t want the stand to rotate or prefer to bolt it to a counter.

    Make sure to save the PivotTable base and assembly pieces in case you decide to reinstall it later.

    1. Using the assembly tool, remove the PivotTable screw and ClickSafe anchor.
      Click to Enlarge
    2. Remove the PivotTable cap.
      Click to Enlarge
    3. Lift the stand off the PivotTable base.

    • Help us improve ShopKeep Support. Was this article helpful?
    • YES   NO